1
resposta

Porque o meu switch está aparecendo como fastethernet 2/1 e não 0/2 como no exemplo

PT3000 Boot Loader (PT3000-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)
Compiled Mon 22-Jul-02 18:57 by miwang
Cisco WS-CSwitch-PT (RC32300) processor (revision C0) with 21039K bytes of memory.
Switch-PT starting...
Base ethernet MAC Address: 0001.97D4.7093
Xmodem file system is available.
Initializing Flash...
flashfs[0]: 1 files, 0 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 64016384
flashfs[0]: Bytes used: 3117390
flashfs[0]: Bytes available: 60898994
flashfs[0]: flashfs fsck took 1 seconds.
...done Initializing Flash.

Boot Sector Filesystem (bs:) installed, fsid: 3
Parameter Block Filesystem (pb:) installed, fsid: 4


Loading "flash:/pt3000-i6q4l2-mz.121-22.EA4.bin"...
########################################################################## [OK]
              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) PT3000 Software (PT3000-I6Q4L2-M), Version 12.1(22)EA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Fri 12-May-06 17:19 by pt_team

Cisco WS-CSwitch-PT (RC32300) processor (revision C0) with 21039K bytes of memory.
Processor board ID FHK0610Z0WC
Running Standard Image
6 FastEthernet/IEEE 802.3 interface(s)

63488K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 0001.97D4.7093
Motherboard assembly number: 73-5781-09 
Power supply part number: 34-0965-01
Motherboard serial number: FOC061004SZ
Power supply serial number: DAB0609127D
Model revision number: C0
Motherboard revision number: A0
Model number: WS-CSwitch-PT
System serial number: FHK0610Z0WC

Cisco Internetwork Operating System Software
IOS (tm) PT3000 Software (PT3000-I6Q4L2-M), Version 12.1(22)EA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Fri 12-May-06 17:19 by pt_team

Press RETURN to get started!


%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

%LINK-5-CHANGED: Interface FastEthernet1/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/1, changed state to up

%LINK-5-CHANGED: Interface FastEthernet3/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3/1, changed state to up


Switch>enable
Switch#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 20
Switch(config-vlan)#name FINANCAS
Switch(config-vlan)#exit
Switch(config)#inter
Switch(config)#interface range fas
Switch(config)#interface range fastEthernet 0/1 - 1/1
                                                  ^
% Invalid input detected at '^' marker.

Switch(config)#interface range fastEthernet 0/1 - 0/2
                                                  ^
% Invalid input detected at '^' marker.

Switch(config)#interface range fastEthernet 0/1 - 2
interface range not validated - command rejected
Switch(config)#interface range fastEthernet 0/1 - 1
Switch(config-if-range)#interface range fastEthernet 0/1 - 2
interface range not validated - command rejected
Switch(config)#interface range fastEthernet 0/2
interface range not validated - command rejected
Switch(config)#interface range fastEthernet 2/1
Switch(config-if-range)#
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#
1 resposta

Olá Wanessa, tudo bem?

Qual o modelo do switch que você está usando? Algumas vezes, dependendo do modelo, a maneira que as portas são numeradas mudam um pouco.